Aluminum alloy bicycle parts is applied to bicycle parts for our Spanish customers. We make black lectrophoresis on this aluminium die casting electrophoresis parts. The material and its surface condition of the black electrophoresis processing is very large. I think it is necessary to pay attention to the selection as much as possible, and the solution is better, and it is related to the black electrophoresis processing. Speaking of which, I think it is a relatively cheap surface solution process and method. Black electrophoresis processing is roughly the same as other electrophoresis processing methods, and it is necessary to carry out surface treatment of the painted parts before spraying. Different spraying methods, different materials and surface conditions, the prescribed surface solutions and processes are all different. Not only is the different surface solution process and solution quality seriously jeopardizing the quality of spraying, but the cost of surface solution is very harmful. Therefore, during the period of process classification, the spraying method, the material of the painted part and the surface condition must be taken into account. It is possible to choose a surface solution process and method with strong systemicity, good solution effect and relatively cheap surface solution.
Product Specification
Customer |
Serial No: |
201012054 |
||||||||||||||||||
Product |
Lot No |
Alloy And Temper |
Dimension (mm) |
|||||||||||||||||
AlSi10Mg |
50*50*45 |
|||||||||||||||||||
Technique Standard |
GB/T3880-2012 |
Composition Standard |
GB/T3190-2008 |
|||||||||||||||||
Chemical Composition % | ||||||||||||||||||||
Element |
Si |
Mg |
Mn |
Cu |
Fe |
Ni |
Zn |
Sn |
Al |
|||||||||||
Standard |
8.0-10.5 |
0.17-0.35 |
0.2-0.5 |
≤0.3 |
≤0.9 |
≤0.15 |
≤0.25 |
≤0.01 |
Remainder |
|||||||||||
Actual |
9.5 |
0.25 |
0.37 |
0.21 |
0.84 |
0.14 |
0.23 |
0.01 |
||||||||||||
Mechanical Property | ||||||||||||||||||||
Sampling |
Tensile Strength (MPa) |
Yield Strength (MPa) |
Elongation (%) |
|||||||||||||||||
—— |
Standard |
Actual |
Standard |
Actual |
Standard |
Actual |
||||||||||||||
≥195 |
250 |
—— |
—— |
≥1.5 |
2.9 |
|||||||||||||||
Cup Bulge |
—— |
—— |
90°bend |
|||||||||||||||||
Earing(%) |
—— |
—— |
Hardness |
≥65HB |
||||||||||||||||
Surface Control |
Good |
Dimension Control |
Meet Standard |
|||||||||||||||||
Hydrogen Content Standard Value (ml/100gAl) |
—— |
Hydrogen Content Actual Value (ml/100gAl) |
—— |
Our company
Ningbo Free Trade Zone Quanxing Moulding Co.,Ltd is oem customized die casting manufacturer, who can make die casting molds and products as customers' design over 15 years. Quanxing can make both small aluminum bicycle parts and large aluminum bicycle parts. Because die casting is very suit for making aluminum high pressure bicycle parts, high quality aluminum bicycle parts, high precision aluminum bicycle parts, and high hardness aluminum bicycle parts, Quanxing also cooperate with many bicycle companies.
We use 3D software ,like PRO-E, SOLIDWORKS, UG.
Quanxing has nearly 160 steady customers communities. Products & moulds are mainly exported to European Union,North America,South America , Australia and more than 20 countries.
Certificate
We have ISO9001 and SGS certificates. And we will have 100% inspection before shipment. From now on , we already made more than 500 kinds of die casting products.
The Differences for the Surface finish
The differences between electrophoresis, powder coating and painting are as follows:
-- Whether electrophoresis, powder coating and painting can be masked is different.
1. Electrophoresis is inconvenient to shield.
2. Powder coating and painting can be masked.
-- Whether electrophoresis, powder coating and painting can be treated differently.
1. After electrophoresis film formation, the surface insulation cannot be treated twice.
2. Powder coating and painting can be repeated for many times.
-- The suitable materials for electrophoresis, powder coating and painting are different.
1. Electrophoresis is suitable for all products with conductive surfaces.
2. Powder coating and painting are suitable for almost all product surface treatments.
-- The advantages and disadvantages of electrophoresis, powder coating and painting are different.
1. Electrophoresis advantages: water-based coatings are environmentally friendly, with high coating utilization, good corrosion resistance, high treatment efficiency, and low cost per unit area;
Disadvantages: The color is single and difficult to adjust at will. The equipment has a large investment in the early stage. It is only suitable for conductive products and requires high temperature curing.
2. Advantages of powder coating: environmentally friendly coatings, high utilization rate of coatings, can be used in various colors;
Disadvantages: thick film thickness, high temperature curing.
3. Advantages of painting: It can be processed in a variety of different colors, and various performance coatings are more selective;
Disadvantages: low utilization rate, less environmental protection, high fire hazard, and dust-free workshop required.
Package
As for packaging, we will use bubble bags to protect each product. Several products are packed in a carton.If you need to transport your goods by sea, we will make you a fumigation-free wooden pallet to hold your goods.If you will choose are transport, we will not use the pallet..
Bubble Bag | Carton |
Load to Container |
Pallet |
Transportation
We support EXW, FOB, CIF and so on. We usually send samples by express(Door to door), such as DHL, TNT, FedEx, UPS, EMS and so on. Batch goods shipments can be shipped by sea or air transport according to the customers demand.
Express
Sea transport | Air transport |
FAQ:
1. Q:Are you a factory or trade company?
A: We are a factory. We can provide you one-stop service, from mold design to finish part and arrange the shipment.
2. Q:Where is your factory?
A: Our factory located in Ningbo city, Zhejiang Province, China, which is the hometown of mould in China.
3. Q: How can you assure the product quality?
A: We will have 4 times quality inspection for production:
1. Material incoming control : We ask our material supplier make material test report and checked.
2. Inline inspection : we will make random inspection during production.
3. 100% inspection : making 100% inspection before packing.
4. Final inspection : doing random inspection after products packed.
http://www.qx-diecasting.com/